Teledyne LeCroy HDO6104

PRTNRS692
Puan: 0
  • Teledyne LeCroy HDO6104

500 MHz, 2.5 GS/s, 4 Ch, 50 Mpts/Ch 12-bit HD Oscilloscope with 12.1" WXGA Touch Display

0,00 + KDV
Bu ürün 4-6 Hafta içinde kargoya verilir.

Teknik Özellikler

Vertical System

Bandwidth 1 GHz
Analog Bandwidth (Max) 1 GHz
Analog Bandwidth @ 50 Ω (-3 dB) (ProBus Input) 1 GHz
(≥1 mV/div)
Analog Bandwidth @ 1 MΩ (-3 dB) (ProBus Input) 500 MHz (typical)
Rise Time (10-90%, 50 Ω) 450 ps (typical)
Input Channels 4
Bandwidth Limiters 20MHz, 200MHz
Input Impedance 1 MΩ ± 2.0% || 15 pF, 50 Ω ± 2.0%
Input Coupling 1 MΩ: AC, DC, GND; 50 Ω: DC, GND
Maximum Input Voltage 50 Ω: 5 Vrms,
1 MΩ: 400 V max
(DC + Peak AC ≤ 10 kHz)
Channel-Channel Isolation DC-400MHz > 1000:1; 400MHz up to rated BW > 300:1
Vertical Resolution 12 bits; up to 15 bits with enhanced resolution (ERES)
Sensitivity 50 Ω: 1 mV-1 V/div, fully variable;
1 MΩ: 1 mV-10 V/div, fully variable
DC Gain Accuracy ±(0.5%) F.S, offset at 0 V
DC Vertical Gain Accuracy (Gain Component of DC Accuracy) ±(0.5%) F.S, offset at 0 V
Offset Range 50 Ω
±1.6 V @ 1 mV - 4.95 mV/div
±4 V @ 5 mV - 9.9 mV/div
±8 V @ 10 mV - 19.8 mV/div
±10 V @ 20 mV - 1 V/div

1 MΩ
±1.6 V @ 1 mV - 4.95 mV/div
±4 V @ 5 mV - 9.9 mV/div
±8 V @ 10 mV - 19.8 mV/div
±16 V @ 20 mV - 100 mV/div
±80 V @ 102 mV - 198 mV/div
±160 V @ 200 mV - 1 V/div
±400 V @ 1.02 V - 10 V/div
Offset Accuracy +/-(1.0% of offset setting + 0.5%FS + 0.02% of max offset + 1mV)
DC Vertical Offset Accuracy ±(1.0% of offset setting + 0.5%FS + 0.02% of max offset + 1mV)
 

Horizontal System

Timebases Internal timebase common to 4 input channels; an external clock may be applied at the auxiliary input
Time/Division Range 20 ps/div - 5 ks/div with standard memory (up to 10 ks/div with -L memory, 25 ks/div with -XL memory);
RIS available at ≤ 10 ns/div; Roll Mode available at ≥ 100 ms/div and ≤ 5 MS/s
Clock Accuracy +/-2.5ppm + 1.0ppm/year from calibration
Jitter Noise Floor 700fs
Trigger and Interpolator Jitter ≤ 4 ps RMS (typical)
<0.1 ps RMS (typical, software assisted)
Channel-Channel Deskew Range ±9 x time/div. setting, 100 ms max., each channel
External Timebase Reference (Input) 10MHz +/-25ppm at 0 to 10dBm into 50Ohms
External Timebase Reference (Output) 10MHz, 3.5 dBm +/-1dBm, syncronized to reference being used (internal or external reference)
via LBUS BNC adaptor
External Clock DC to 100 MHz; (50 Ω/1 MΩ), EXT BNC input, Minimum rise time and amplitude requirements apply at low frequencies.
 

Acquisition System

Single-Shot Sample Rate/Ch 2.5 GS/s on 4 Ch
Random Interleaved Sampling (RIS) 125 GS/s for repetitive signals (20 ps/div to 10 ns/div)
Maximum Trigger Rate 1,000,000 waveforms/second (in Sequence Mode, up to 4 channels)
Intersegment Time 1 µs
Maximum Acquisition Memory 250 Mpts (4 Ch operation)
Standard Memory (4 Ch / 2 Ch / 1Ch) (Number of Segments) 50M / 50M / 50M
(30,000)
Memory Options (4 Ch / 2 Ch / 1Ch)
(Number of Segments)
L- Option: 
100M / 100M / 100M
(60,000)
XL - Option:
250M / 250M / 250M
(65,000)
 

Acquisition Processing

Averaging Summed averaging to 1 million sweeps; continuous averaging to 1 million sweeps
Enhanced Resolution (ERES) From 12.5 to 15 bits vertical resolution
Envelope (Extrema) Envelope, floor, or roof for up to 1 million sweeps
Interpolation Linear or Sin x/x
 

Triggering System

Modes Normal, Auto, Single, and Stop
Sources Any input channel, Ext, Ext/10, or line; slope and level unique to each source (except line trigger)
Coupling Mode DC, AC, HFRej, LFRej
Pre-trigger Delay 0-100% of memory size (adjustable in 1% increments of 100 ns)
Post-trigger Delay 0-10,000 Divisions in real time mode, limited at slower time/div settings or in roll mode
Hold-off by Time or Events From 2 ns up to 20 s or from 1 to 99,999,999 events
Internal Trigger Range ±4.1 div from center (typical)
Trigger Sensitivity with Edge Trigger ProBus Inputs 0.9 division: 10 MHz
1.0 divisions: 200 MHz
1.5 divisions: 500 MHz
2.0 divisions: 1 GHz
External Trigger Sensitivity, (Edge Trigger) 0.9 division: 10 MHz
1.0 divisions: 200 MHz
1.5 divisions: 500 MHz
2.0 divisions: 1 GHz
Max. Trigger Frequency, SMART Trigger 1GHz
External Trigger Input Range Ext (±0.4 V); Ext/10 (±4 V)
 

Basic Triggers

Edge Triggers when signal meets slope (positive, negative, or either) and level condition.
Window Triggers when signal exits a window defined by adjustable thresholds
TV-Composite Video Triggers NTSC or PAL with selectable line and field; HDTV (720p, 1080i, 1080p) with selectable frame rate (50 or 60 Hz) and Line; or CUSTOM with selectable Fields (1-8), Lines (up to 2000), Frame Rates (25, 30, 50, or 60 Hz), Interlacing (1:1, 2:1, 4:1, 8:1), or Synch Pulse Slope (Positive or Negative).
 

SMART Triggers

State or Edge Qualified Triggers on any input source only if a defined state or edge occurred on another input source. Delay between sources is selectable by time or events.
Qualified First In Sequence acquisition mode, triggers repeatably on event B only if a defined pattern, state, or edge (event A) is satisfied in the first segment of the acquisition. Holdoff between sources is selectable by time or events.
Dropout Triggers if signal drops out for longer than selected time between 1 ns and 20 s.
Pattern Logic combination (AND, NAND, OR, NOR) of 5 inputs (4 channels and external trigger input). Each source can be high, low, or don?t care. The High and Low level can be selected independently. Triggers at start or end of the pattern.
 

SMART Triggers with Exclusion Technology

Glitch Triggers on positive or negative glitches with selectable widths. minimum width 1.5ns, Maximum Width: 20s
Width (Signal or Pattern) Triggers on positive or negative glitches with selectable widths.
minimum width 1.5ns, Maximum Width: 20s
Interval (Signal or Pattern) Triggers on intervals selectable between 1 ns and 20 s.
Timeout (State/Edge Qualified) Triggers on any source if a given state (or transition edge) has occurred on another source.
Delay between sources is 1 ns to 20 s, or 1 to 99,999,999 events.
Runt Trigger on positive or negative runts defined by two voltage limits and two time limits. Select between 1 ns and 20 ns.
Slew Rate Trigger on edge rates. Select limits for dV, dt, and slope. Select edge limits between 1 ns and 20 ns.
Exclusion Triggering Trigger on intermittent faults by specifying the expected behavior and triggering when that condition is not met
 

Cascade (Sequence) Triggering

Capability Arm on "A" event, then Trigger on "B" event. Or Arm on "A" event, then Qualify on "B" event, and Trigger on "C" event.
Types Cascade A then B: Edge, Window, Pattern (Logic) Width, Glitch, Interval, Dropout, or Measurement. Measurement can be on Stage B only.
Cascade A then B then C (Measurement): Edge, Window, Pattern (Logic), Width, Glitch, Interval, Dropout, or Measurement. Measurement can be on Stage C only.
Cascade A then B then C: Edge, Window, Pattern (Logic)
Holdoff Holdoff between A and B or B and C is selectable by time (1ns to 20s) or number of events.
Measurement trigger selection as the last stage in a Cascade precludes a holdoff setting between the prior stage and the last stage.
 

Low Speed Serial Protocol Triggering (Optional)

Optionally available I2C, SPI (SPI, SSPI, SIOP), UART-RS232, CAN, LIN, FlexRay, MIL-STD-1553, USB 1.x/2.0, AudioBus
 

Measurement Trigger

Measurement Trigger Capability Select from a large number of measurement parameters trigger on a measurement value with qualified limits. Can be used as only trigger or last event in a Cascade Trigger.
 

Color Waveform Display

Type Color 12.1" widescreen flat panel TFT-Active Matrix with high resolution touch screen
Resolution WXGA; 1280 x 800 pixels.
Number of traces Display a maximum of 16 traces. Simultaneously display channel, zoom, memory and math traces.
Grid Styles Auto, Single, Dual, Quad, Octal, X-Y, Single+X-Y, Dual+X-Y
Waveform Representation Sample dots joined, or sample dots only
 

Internal Waveform Memory

Internal Waveform Memory 4 active waveform memory traces (M1-M4) store 16 bit/point full length waveforms. Waveforms can be stored to any number of files limited only by the data storage media capacity.
 

Integrated Second Display

Type Supports touch screen integration of user-supplied second display with split-grid capability.
Resolution (Note: touch screen driver for second display may not be a Fujitsu driver)
 

Analog Persistence Display

Analog and Color-Graded Persistence Variable saturation levels; stores each trace?s persistence data in memory
Persistence Types Select analog, color, or three-dimensional
Trace Selection Activate persistence on all or any combination of traces
Persistence Aging Select from 500 ms to infinity
Sweep Display Modes All accumulated, or all accumulated with last trace highlighted
 

Processor/CPU

Type Intel Core i5, 2.5 GHz (or better)
Processor Memory 8 GB standard
Operating System Microsoft Windows® 7 Pro 64 bit Embedded
Real Time Clock Date and time displayed with waveform in hardcopy files. SNTP support to synchronize to precision internal clocks.
 

Zoom Expansion Traces

Zoom Expansion Traces Display up to 8 Zoom and 8 Math/Zoom traces
 

Setup Storage

Front Panel and Instrument Status Store to the internal hard drive, over the network, or to a USB-connected peripheral device.
 

Interface

Remote Control Via Windows Automation, or via LeCroy Remote Command Set
GPIB Port Supports IEEE - 488.2 (External)
Ethernet Port Supports 2 10/100/1000BaseT Ethernet interface (RJ45 ports)
USB Ports Minimum 6 total (incl. 2 front panel) USB 2.0 ports support Windows compatible devices
USB Device Port 1 USBTMC port
External Monitor Port 15 pin D-Type WXGA compatible DB-15 to support customer-supplied external monitor.
Includes support for extended desktop operation with WXGA resolution on second monitor.
 

Auxiliary Input

Signal Types Select External Trigger or External Clock Input on the front panel
Coupling 50 Ω: DC; 1 MΩ: AC, DC, GND
Max. Input Voltage 50 Ω: 5 Vrms; 1 MΩ: 400 Vmax (DC + Peak AC ≤ 5 kHz)
 

Auxiliary Output

Signal Types Select from control signals or Off
Output Signal 500 Hz-1 MHz square wave or DC level; 50 mV-1 V into 1 MΩ
Control Signals Trigger enabled, trigger out, pass/fail status, off
Connector Type BNC, located on rear panel
 

Automatic Setup

Auto Setup Automatically sets timebase, trigger, and sensitivity to display a wide range of repetitive signals
Find Vertical Scale Automatically sets the vertical sensitivity and offset for the selected channel to display a waveform with the maximum dynamic range
 

Probes

Probes Qty. (4) ÷10 Passive Probes
Probe System Probus. Automatically detects and supports a variety of compatible probes
Scale Factors Automatically or manually selected depending on probe used
Calibration Output Default is 1kHz square wave, 1Vp-p (typical), output to probe hook. Settable from 250 Hz to 1 MHz square wave; 50 mV to 1.0V.
 

Power Requirements

Voltage 100-240 VAC ±10% at 45-66 Hz; 110-120 VAC ±10% at 380-420 Hz; Automatic AC Voltage Selection; Installation Category 300 V CAT II
Max. Power Consumption 350 VA
 

Environmental and Safety

Temperature (Operating) +5 °C to +40 °C
Temperature (Non-Operating) -20 °C to +60 °C
Humidity (Operating) 5% to 80% relative humidity (non-condensing) up to +31 °C.
Upper limit derates to 50% relative humidity (non-condensing) at +40 °C.
Humidity (Non-Operating) 5% to 95% relative humidity (non-condensing) as tested per MIL-PRF-28800F
Altitude (Operating) Up to 10,000 ft. (3048 m) at or below +25 °C
Altitude (Non-Operating) Up to 40,000 ft. (12,192 m)
Random Vibration (Operating) 0.31 grms 5 Hz to 500 Hz, 15 minutes in each of three orthogonal axes
Random Vibration (Non-Operating) 2.4 grms 5 Hz to 500 Hz, 15 minutes in each of three orthogonal axes
Functional Shock 30 g peak, half sine, 11 ms pulse, 3 shocks (positive and negative) in each of three orthogonal axes, 18 shocks total
 

Physical Dimensions

Dimensions (HWD) 11.48"H x 15.72"W x 5.17"D (291.7 mm x 399.4 mm x 131.31 mm)
Weight 12.9 lbs. (5.86 kg.)
Shipping Weight 20.2 lbs. (9.2 kg)
 

Certifications

Certifications UL 61010-1 (3rd Edition), UL 61010-2-030 (1st Edition)
CAN/CSA C22.2 No. 61010-1-12,
 

Warranty and Service

Warranty and Service 3-year warranty; calibration recommended annually.
Optional service programs include extended warranty, upgrades, and calibration services.

 

Yorumlar

Bu ürün için toplam 0 yorum yapılmıştır. Yorum yapabilmeniz için giriş yapmanız gerekir Giriş Yap

Taksit Seçenekleri

CARDFINANS
2 Taksit3 Taksit6 Taksit
0,00 X 2 = 0,000,00 X 3 = 0,000,00 X 6 = 0,00
MAXIMUM
2 Taksit3 Taksit6 Taksit
0,00 X 2 = 0,000,00 X 3 = 0,000,00 X 6 = 0,00
PARAF
2 Taksit3 Taksit6 Taksit
0,00 X 2 = 0,000,00 X 3 = 0,000,00 X 6 = 0,00
WORLD
2 Taksit3 Taksit6 Taksit
0,00 X 2 = 0,000,00 X 3 = 0,000,00 X 6 = 0,00
  • Hızlı Teslimat
  • Optical Fiber Fusion Splicer
  • GÜRÜLTÜ FİGÜR ANALİZÖRLERİ
  • Partner Electronic Güvencesi
  • Güvenli Ödeme